Short Torque Absorber 66-500

QuickCar Torque Absorbers increase forward bite off the corner and hold traction down the straight, and they do it with less weight than spring-style units. CNC-machined construction with an internal brass bushing and grease fittings keeps them from...

Long Torque Absorber 66-499

QuickCar Torque Absorbers increase forward bite off the corner and hold traction down the straight, and they do it with less weight than spring-style units. CNC-machined construction with an internal brass bushing and grease fittings keeps them from...

Intermediate Torque Absorber 66-400

QuickCar Torque Absorbers increase forward bite off the corner and hold traction down the straight, and they do it with less weight than spring-style units. CNC-machined construction with an internal brass bushing and grease fittings keeps them from...

Suspension Tube Ruler 66-100

Suspension tubes and tie rods have to be measured rod end to rod end, and a tape hooked over a heim joint never lands in the same place twice. This ruler indexes off the rod ends themselves. A black Powdercoat ruler with adapters for 1/2 Inch to 3/4 Inch...

Tire Caliper 64-706

Stagger has to be checked repeatedly through a night, and a tape wrapped around a hot tire is slow and inconsistent. A box style caliper takes the reading in one movement. Machined from aluminum and covering a 65 Inch to 115 Inch range, it opens across...

Aluminum Toe Plates 64-704

Toe measured with a tape and a straight edge is a two person job with a wide margin for error. Toe plates make it accurate and repeatable by one person. A pair of high quality aluminum toe plates supplied with two 12 Foot tape measures. Lean the plates...

12Ft. Tape Measure 64-703

Toe and other setup checks need a tape that stays straight when it is extended, not one that folds over halfway across the car. This one is rigid enough to hold its own line. A 3/4 Inch wide tape measuring up to 12 Foot, suited to checking toe in and out...

GM/Metric Caliper Pressure Test Kit 64-511

Brake bias set by feel is a guess. A QuickCar Brake Caliper Pressure Test Kit reads the actual pressure at each caliper, so bias can be set and brake problems tracked down with numbers instead of seat-of-the-pants. This kit includes two 0-1,000 PSI...

White Tire Marker 64-400

Tire information written on the tire itself cannot be lost, mixed up, or left on the pit cart. A crayon marker is the fastest way to get pressure, position, and condition in front of the whole crew. A white tire marker for noting air pressure settings,...

2 Barrel Throttle Stop 64-158

A throttle that does not return fully is a safety issue and a tuning problem at the same time. A rigid stop gives the linkage a fixed, repeatable resting point. CNC-machined black anodized aluminum with an adjustable stop, designed for popular Holley two...

4 Barrel Throttle Stop 64-157

A throttle that does not return fully is a safety issue and a tuning problem at the same time. A rigid stop gives the linkage a fixed, repeatable resting point. CNC-machined black anodized aluminum with an adjustable stop, designed for popular Holley...

Silver 5/16" Carburetor Nut 64-149

A wing nut that needs a tool is a wing nut that slows down an air cleaner change, and one without a seal lets unfiltered air past. This thumb screw nut solves both. Machined aluminum in a raw mill silver finish, fitting 5/16 Inch-18 threads and supplied...

Aluminum Carburetor Hat with O-Ring 64-146

QuickCar Carburetor Hat helps protect the engine from dirt, debris, and other contaminants when the air cleaner has been removed during maintenance, setup, transportation, or storage. Designed to fit carburetors with a 5-1/8-inch air cleaner flange, the...

Short Pit Socket 64-078

Pit stop time is won and lost at the wheel, and a socket that will not stay on the nut costs more than any tenth found on track. These American made pit sockets are built for the abuse. A 2-1/4 Inch long steel socket with 1/2 Inch drive. The shorter body...

Impact Crimper 64-020

A battery cable terminal crimped with pliers or a hammer and punch is a joint that will heat up and fail. An impact crimper forms the barrel properly, all the way around. Built for permanent termination of standard power rings onto battery cables,...